|
| 网站首页 | 英语新闻 | 英语学习中心 | 英语图片 | 下载 | 购书 | 培训 | 留言 | Study Chinese | | ||
|
||
|
||
游艇专业英语词汇(P3) |
||
作者:佚名 文章来源:不详 点击数: 更新时间:2006-8-6 |
||
卫生器具 plumbing fixture 铅锤线 plumb line 气力起动阀 pneumatic starting valve 问题导向语言 POL (= problem oriented language) 多相 polyphase 多变效率(气涡轮机) polytropic efficiency 箱筏 pontoon raft 焊接后热处理 post weld heat treatment (PWHT) 位差 potential difference 位降 potential drop 焊剂填入电焊 powder plug arc welding (P.P.A.) 先期点火 preignition (or premature ignition) 袋压法(FRP) pressure bag method 复压涡轮机 pressure compounded turbine 压力开关 pressure switch 压水式反应器 pressurized water reactor (PWR) 防动索,固定索 preventer 主要项目,主要特性 principal particulars 虚功原理 principle of vitual work 程控 program control 投影,凸起 projection 限载重,限负荷 proof load 安全限应力 proof stress 螺桨轴转速计 propeller shaft revolution indicator 比例限界 proportional limit 粮食库 provision room 保健局卫生规则 public health service's sanitary requirement 乳头通风系统 Punkah-Louver system 推[型拖]船 push boat (or pusher) 截锥头铆钉 pan head rivet 粮食库 provision room 定期船,邮船 packet boat 起迫紧钩 packing hook 加强焊料 padding (or reinforce) 分批编号 pallet number 拍击 panting 要目表 particular sheet 总钥 pass key 节圆直径 PCD (= pitch circle diameter) 最高载重,尖峰负荷 peak load 波来铁,波来体 Pearlite 剥离强度 peel strength 摆式冲击试验机 pendulum impact testing machine 多孔板 perforated plate 性能曲线 performance curve 性能试验 performance test 永久变形 permanent set 相位指示器 phase indicator 相移 phase shift 酚树脂涂料 phenolic resin paint 酚树脂 phenolics 物理试验 physical test 码头 pier 柱形浮筒,柱形浮标 pillar buoy 引水船桥 pilot bridge 引水旗 pilot flag 弯管器 pipe bender 装管工 pipe fitter 管格架 pipe grid 管路通道 pipe passage 管架 pipe rack 管绞刀 pipe reamer 管螺纹 pipe thread 管路布置图 piping arrangement 活塞冷却油泵 piston cooling oil pump 活塞头,活塞冠 piston head (or crown) 臂轴起重机 pivot gib crane 艉浮扬[前抱台]压力(下水) pivotting pressure 抽排水布置图 pumping and drainage plan 面积仪 planimeter 塑料发泡材,泡沫塑料 plastics foam 塞孔 plug hole 塞孔焊接 plug welding 柱塞 plunger 小燃料舱 pocket bunker 游隙规 poker gauge 极坐标 polar coordinate 极惯性矩 polar moment of inertia 聚酯树脂 polyester resin 起重船 pontoon crane 艉艛栏杆 poop rail 可携压载 portable ballast 后热(焊接) post heating 门形柱梁 post portal 百万分之一 [容积比] PPM (= parts per million) 预造 pre-erection 压力 pressure 压力计程仪 pressure log 帆锥,索针,火叉 pricker 初次燃烧区 primary zone 问题导向语言 problem oriented language (POL) 投影面积比 projected area ratio 螺桨[模]单独试验 propeller experiment in open water 螺桨定律 propeller law 螺桨支架 propeller strut 比例控制 proportional control 防护衣具 protective ware 牵引速率 pulling speed 冲剪机 punching and shearing machine 抽油灰枪 putty gun (or red lead injector) 并流热交换器 parallel flow heat exchanger (or regenerator) 并流涡轮机 parallel flow turbine 并联运转(电),并列运转 parallel running 本体金属,母材(电焊) parent metal 客货轮 passenger cargo ship 旅客渡船 passenger ferry 定期客轮,邮轮 passenger liner 客船安全证书 passenger ship safety certificate 送[铆钉]火钳 passing tongs 贴补,补缀,补绽 patch 托架,轴架 pedestal 剪断破面率 percent shear 完全驱气 perfect scavening 汽油机 petrol engine 石油柜 petroleum tank 相位仪 phase meter 领港升降机 pilot hoist 销管式热交换器 pin tube type heat exchanger 管螺纹机 pipe screw cutting machine (or pipe threading machine) 管扳钳 pipe wrench (or spanner) 纵摇周期 pitching period 平钩 plain hook 管路图 piping plan 泵送图 pumping plan 板缘加工(电焊) plate edge preparation 塞,插头,舷窗外盖 plug 聚苯乙烯发泡材 polystyrene (PS) foam 聚乙烯 polyvinyl 舷窗 port hole 比压器,计器用变压器 potential transformer 呼吸阀 pressure vacuum relief valve (or breather) 主防壁(LNG船) primary barrier [纵向]棱块系数,棱形系数 prismatic coefficient 处理机,处理程序 processor 反射式磁罗经 projector compass 临时设计 provisional design 冲压模板 punchig template 跳动阀 puppet (or poppet) valve 压力容积线图 PV (= pressure volume) diagram 永久煤舱 permanent coal bunker 汽油 petrol 相位超前 phase lead 生铁 pig iron 轴道轴承 pillow block (or tunnel shaft bearing) 前导点火 pilot ignition 舵针承 pintle bearing 销形阀 pintle valve 布管船 pipelayer 螺距规 pitch gauge 灰泥,石膏 plaster 普林索式载重标志 Plimsoll's mark 配管工作 plumber work 艏潜 plunge 气力铆机 pneumatic riveter 竿钓渔船 pole and line fishing boat 聚氯乙烯 polyvinyl chloride (PVC) 箱形舱盖 pontoon hatch cover 瓷管 porcelain tube 多孔性,气孔 porosity 活动装具 portable fittings 排水口盖 port flap (or lid) 流动点 pour point 预组 preassembling 预热器 preheater 压力角 pressure angle 原动机 prime mover 形状曳力 profile drag 定程序负荷 programme load 投影面积 project area 保证试验,安全限试验 proof test 推进器,螺桨 propeller 螺桨泵 propeller pump 比例尺 proportioner 推进效率 propulsive coefficient (or efficiency) 议定书 protocol 粮食吊车 provision crane 脉冲电弧焊 pulse arc welding 泵 pump 移动式泵 portable pump 泵送图 pumping plan 复滑车 purchase block 按钮开关 push-button switch 油灰泵 putty pump 管绞刀 pipe reamer 转向轴心(船运动) pivoting point 支柱布置图 pillar plan 平面位置指示器 plane position indicator (PPI) 平行炉膛 plan furnace 龙门刨床 planing machine 木板,板 plank 塑性 plasticity 板制桅柱 plated mast 游艇 pleasure yacht 艏突部 plowing 犁钢 plow steel 塞规 plug gauge 卫生排水 plumbing drain 气压测深仪 pneumacator (or teledepth) 接地极性 polarity of ground 瓷便器 porcelain bowl 瓷绝缘体,瓷碍子 porcelain insulator 船籍港 port of registry 预燃室 precombustion chamber 压力空气泵 pressure air pump 压力降 pressure drop 压焓图 pressure-enthalpy diagram 压力比 pressure ratio 压容图 pressure-volume (P-V) diagram 预力 prestressing 级进分段焊接顺序 progressive block welding sequence 投光灯,投影机 projector 螺[桨]叶,?叶 propeller blade 螺[桨节]距 propeller pitch 比例分规 proportional dividers (or compasses) 推进效率 propulsive efficiency (or coefficient) 凸角 protrude angle 校准杆 proving (or calibrating) lever 脉动复现率 PRR (= pulse recurrence rate) 脉冲反复频率 pulse repetition frequency 净油柜 purified oil tank 推拉索 push/pull cable 泄气压力(安全阀) popping pressure 压力容器 pressure container 压力壳(潜艇) pressure hull 压力泵 pressure pump 压力焊接,锻接 pressure welding 主空气,初级空气 primary air 主应力 principal stress 重迭原理 principle of superposition 程序 procedure 过程控制 process control 程序包 program package 螺桨正面 propeller face 螺桨填料 propeller filler 螺桨马力 propeller (or screw) horsepower 螺桨船体涡空泡 propeller-hull vortex cavitation (PHV) 螺桨柱 propeller post 进 propulsion 公用室 public room 搅炼铁 puddled iron 粉煤 pulverised coal 磨粉机 pulveriser 驱气,冲洗,排气 purging 高温计 pyrometer 释放点 point of release 压力损失系数 pressure loss coefficient 压力试验 pressure test 压[力]时[间]图,压力历程图 pressure-time (P-T) diagram 抓斗挖泥船 priestman (or grab) dredger 初级齿轮 primary pinion 主电源 primary source 投影图 projected plan 散步甲板 promenade deck 艉轴 propeller (or screw, or stern, or tail) shaft 人员转移舱 PTC (= personnel trans- portation capsule) 搅炼法 puddling process 泵胴 pump barrel 泵体 pump chamber 泵引擎 pump (or pumping) engine 冲孔台 punch table 压水式反应器 PWR (= pressurized water reactor) 推杆(柴油机) push rod 螺桨面积比 propeller area ratio 安装螺桨压挤力 propeller fitting force ( or push up load) 推进设备 propulsion equipment 量角器 protractor 穿透试验 PT (= penetrant testing) 动力泵 power pump 按钮 push button 油灰,补土 putty 活塞胀圈 piston ring 气力铆机 pneumatic riveter 活塞杆 piston rod 小齿轮轴 pinion shaft 拖板货船 pallet ship 推出式建造法 pushing building system 推杆,挺杆 push rod 推动阀 push valve 焊接后热处理 PWHT (= post weld heat treatment) 厨房用架 plate rack 箱筏 pontoon raft 截锥头粗颈铆钉 pan head and swell neck rivet 截锥头直颈铆钉 pan head with parallel neck rivet 平锯 plate saw 垫环 packing ring 多孔环 perforated ring 客船 passenger ship 客轮 passenger steamer 艉轴 propeller (or screw, or stern, or tail) shaft 管工场 plummer (or plumber) shop 正稳度 positive stability 轻便肋骨压曲器 portable frame squeezer 明轮船 paddle steamer 柱塞弹簧 plunger spring 油漆库 paint store 抗拍纵肋 panting stringer 动力冲程 power stroke 喷漆器 paint sprayer 螺桨转速 propeller speed 安全限应力 proof stress 定期检验 periodical survey 石油柜 petroleum tank 悬摆冲击试验机 pendulum impact testing machine 递增速率试验 progressive speed trial 拍底应力 pounding stress 酸洗槽 pickling tank 活塞弹簧 piston spring 粮食库,给养库 provision store 冲孔台 punch table 冲穿试验 punching test 按钮开关 push-button switch 保证试验 proof test 节距速率(螺桨) pitch speed 掌形螺撑 palm stay 管螺纹 pipe thread 主应力 primary stress 变极开关 pole changing switch 冲击试验 percussion (or impact) test 压力试验 pressure test 尖舱 peak tank 螺桨推力 propeller thrust 石油气 petroleum vapour 客船 passenger vessel 压速复式涡轮机 pressure velocity compound turbine 活塞阀 piston valve 压力容器 pressure vessel 管钳 pipe tongs 机动船 power driven vessel 流线迹流 potential wake 波兰国家标准 PN (= Porska Norma, Poland) 起动注给阀 priming valve 有孔垫圈 perforated washer 塞孔焊接 plug welding 巴拿马运河吨位 Panama Canal tonnage 比压器 potential transformer 并流涡轮机 parallel flow turbine 针阀 pin valve 提动阀 poppet (or puppet) valve 引水船 pilot vessel 美国瓷釉学会 PEI (= Porcelain Enamel Institute, U.S.A.) 推动阀(柴油机) push valve 向导阀 pilot valve 巴基斯坦国家标准 PS (= Pakistan Standards, Pakistan) 波兰验船协会 PR (= Polski Rejestr Statkow) 明轮 paddle wheel 巴基斯坦铁道规范 PRSS (= Pakistand Railway Standard Specification, Pakistan) 砝码 poise weight 管扳钳 pipe wrench 美国管类制造学会 PFI (= Pipe Fabrication Institute, U.S.A.)实践证明经常访问无忧英语教育网 www.51education.net ,能迅速提高你的英语学习能力!积沙成塔,不断提高! 本站所提供的所有信息仅供学校课堂教学及英语学习者学习研究之用,其著作权归原作者及媒体所有。 |
||
文章录入:soosun 责任编辑:soosun |
||
|
||
【发表评论】【加入收藏】【告诉好友】【打印此文】【关闭窗口】 |
最新热点 | 最新推荐 | 相关文章 | ||
节日必备:如何用英语买到称… On her own, but not alone “发疯”的两种新潮英语说法 国外生活必备英文词汇-住宿… 几个流行词 第30课:与选举有关的词汇 雅思范文:谈谈你身边城市交… 禽流感常用英语词汇及生化术… 雅思词汇与句型总结 雅思阅读词汇:自然与科技-… |
网友评论:(只显示最新10条。评论内容只代表网友观点,与本站立场无关!) |
|Sitemap地图 | 设为首页 | 加入收藏 | 联系站长 | 友情链接 | 版权申明 | 网站公告 | 管理登录 | | |||
|