 |
|
|||||||||||||||
| | 网站首页 | 英语新闻 | 英语学习中心 | 英语图片 | 下载 | 购书 | 培训 | 留言 | Study Chinese | | ||
|
|
||
 |
||
|
||
|
|
|||||||||||||||
| | 网站首页 | 英语新闻 | 英语学习中心 | 英语图片 | 下载 | 购书 | 培训 | 留言 | Study Chinese | | ||
|
|
||
|
||
|
||
汽车专业英语词汇(1) |
||
|
作者：佚名 文章来源：不详 点击数： 更新时间：2006-8-6 |
||
轮椅升降机 Wheel chair lift 图例 legend 工位 station 吊运装置 overhead hoist 更衣室 restroom 1号厂房工艺布置方案图 proposal of the Plant I layout 合笼 mate 底盘平移台 chassis shuttle 车辆转移台 bus transfer 前围角板 front wall angle cover 后围侧板 rear wall side cover 保险杠 bumper 三类底盘 three type chassis 左侧围应力蒙皮 R/S stretching skin (road side) 中涂 floating coat 拼装台 collector 切割轮口 wheel -arch cutting 内饰 trim 线束 harness 返工 re-doing 轮罩护板 wheel house 发车前准备 pre-delivery 举升 hoist 小批量产品 be pilot 2 套 two kits 配电站 power transformer substation 裙板 skirt 发动机托架 engine holding frame 诊断报警系统 diagnosis and alarming system 互换性 interchangeability 缩微图纸 microfiche files 总装 final assembly 磷化 phosphating 仪表板 dash board 切齐 trimming 结构完整性 structure integrity 自动愈合的防腐材料 self-healing corrosion preventative material 长途客车 inter-city bus 改装厂 refitting factory 遮阳板 sun visor 随车工具 tool box 钢化玻璃 toughened grass 异形钢管 special steel pipe 全天候空调系统 full range A/C 强制通风 ram-air ventilation 停机时间 downtime 无公害柴油 clean diesel 宽敞悬臂式座椅 roomy cantilevered seat 防滑地板 no-skid floor 织物纹里铝合金 textured aluminum extrution 爬坡能力 grade ability 排水阀 drain valve 除湿器 moisture ejector 怠速时 at idle 琴式驱动桥 banjo type drive axle 通风口 duct 恒温控制 thermostatic control 平衡水箱 surge tank 变光开关 simmer switch 消音器 muffler 防破坏 vandal resistant 聚碳化透镜 poly-carbonate len 镀锌板 galvanized plate 搭接 lap 亮丽的外表 smart apperance 隐藏式固定 concealed fastening 水洼 ponding 发动机中置式客车 bus with under floor engine 组合式客车车身 modular bus body 薄壳式结构 shell construction 衬垫 pad 空气导流板 air deflector 搁梁 shelf beam 腰梁 waist rail 梭梁 stabilizing beam 腰带式安全带 diagonal safety belt 压条 trim strip 嵌条 insertion strip 翼板 fender 斜撑 bracing piece 转向盘回正性试验 test of steering wheel returnability 转向盘转角脉冲试验 steering wheel impulse input test 转向盘转角阶跃输入试验 steering wheel step input or transient state yaw response test 极限侧向加速度试验 limiting lateral acceleration test 汽车平顺性随机输入行驶试验 automobile ride random input running test 汽车平顺性单脉冲输入行驶试验 automobile ride single pulse input running test 汽车悬挂系统固有频率与阻尼比的测定试验 measurement of natural frequency and damping raito of suspension 功率突然变化影响试验 test of effect of sudden power change 收油门后控制试验 test of control at breakway 横风稳定性试验 test of crosswind stability 反冲试验 kick-back test 轮胎爆破响应时间试验 test of burst response of tyre 绕过障碍物试验 obstacle avoidance test 移线试验 lane change test J型转弯试验 test of J turn 频率响应时间试验 frequency response test 瞬态响应时间试验 transient response test 阶路响应时间试验 step response test 脉冲响应试验 pulse response test 静态操舵力试验 static steering effort test 悬架举升试验 jack-up test of suspension 耐翻倾试验 test of overturning immunity 轮辋错动试验 rim slip test 风洞试验 wind tunnel test 制动稳定性试验 test of braking stability 最小转弯直径试验 minimum turning diameter test 操舵力试验 steering effort test 类型 type 发动机 engine 内燃机 intenal combusiton engine 动力机装置 power unit 汽油机 gasoline engine 汽油喷射式汽油机 gasoline-injection engine 火花点火式发动机 spark ignition engine 压燃式发动机 compression ignition engine 往复式内燃机 reciprocating internal combustion engine 化油器式发动机 carburetor engine 柴油机 diesel engine 转子发动机 rotary engine 旋轮线转子发动机 rotary trochoidal engine 二冲程发动机 two-stroke engine 四冲程发动机 four-stroke engine 直接喷射式柴油机 direct injection engine 间接喷射式柴油机 indirect injection engine 增压式发动机 supercharged engine 风冷式发动机 air-cooled engine 油冷式发动机 oil-cooled engine 水冷式发动机 water-cooled engine 自然进气式发动机 naturally aspirated engine 煤气机 gas engine 液化石油气发动机 liquified petroleum gas engine 柴油煤气机 diesel gas engine 多种燃料发动机 multifuel engine 石油发动机 hydrocarbon engine 双燃料发动机 duel fuel engine 热球式发动机 hot bulb engine 多气缸发动机 multiple cylinder engine 对置活塞发动机 opposed piston engine 对置气缸式发动机 opposed-cylinder engine 十字头型发动机 cross head engine 直列式发动机 in-line engine 星型发动机 radial engine 筒状活塞发动机 trunk-piston engine 斯特林发动机 stirling engine 套阀式发动机 knight engine 气孔扫气式发动机 port-scavenged engine 倾斜式发动机 slant engine 前置式发动机 front-engine 后置式发动机 rear-engine 中置式发动机 central engine 左侧发动机 left-hand engine 右侧发动机 right-hand engine 短冲程发动机 oversquare engine 长冲程发动机 undersquare engine 等径程发动机 square engine 顶置凸轮轴发动机 overhead camshaft engine 双顶置凸轮轴发动机 dual overhead camshaft engine V形发动机 V-engine 顶置气门发动机 valve in-head engine 侧置气门发动机 side valve engine 无气门发动机 valveless engine 多气门发动机 multi-valve engine 卧式发动机 horizontal engine 斜置式发动机 inclined engine 立式发动机 vertical engine W形发动机 w-engine I形发动机 I-engine L形发动机 L-engine F形发动机 F-engine 性能 performance 二冲程循环 two-stroke cycle 四冲程循环 four-stroke cycle 狄塞尔循环 diesel cycle 奥托循环 otto cycle 混合循环 mixed cycle 定容循环 constant volume cycle 工作循环 working cycle 等压循环 constant pressure cycle 理想循环 ideal cycle 热力循环 thermodynamic cycle 冲程 stroke 活塞行程 piston stroke 长行程 long stroke 上行程 up stroke 下行程 down stroke 进气行程 intake stroke 充气行程 charging stroke 压缩行程 compression stroke 爆炸行程 explosion stroke 膨胀行程 expansion stroke 动力行程 power stroke 排气行程 exhaust stroke 膨胀换气行程 expansion-exchange stroke 换气压缩行程 exchange-compression stroke 止点 dead center 上止点 top dead center(upper dead center) 下止点 lower dead center(bottom dead center) 上止点前 budc(before upper dead center) 上止点后 atdc(after top dead cetner) 下止点前 bbdc(before bottom dead center) 下止点后 abdc(after bottom dead center) 缸径 cylinder bore 缸径与行程 bore and stroke 空气室 energy chamber 气缸余隙容积 cylinder clearance volume 燃烧室容积 combustion chamber volume 气缸最大容积 maximum cylinder volume 压缩室 compression chamber 排气量 displacement 发动机排量 engine displacement 活塞排量 piston swept volume 气缸容量 cylinder capacity 单室容量 single-chamber capacity 容积法 volumetry 压缩比 compression ratio 临界压缩比 critical compression ratio 膨胀比 expansion ratio 面容比 surface to volume ratio 行程缸径比 stroke-bore ratio 混合比 mixture ratio 压缩压力 compression pressure 制动平均有效压力 brake mean effective pressure(bmep) 空燃比 air fuel ratio 燃空比 fuel air ratio 燃料当量比 fuel equivalence ratio 扭矩 torque 单缸功率 power per cylinder 升功率 power per liter 升扭矩 torque per liter 升质量 mass per liter 减额功率 derating power 输出马力 shaft horsepower 马力小时，马力时 horsepower-hour 总马力 gross horse power 总功率 gross power 净功率 net power 燃油消耗量 fuel consumption 比燃料消耗率 specific fuel consumption 空气消耗率 air consumption 机油消耗量 oil consumption 有效马力 net horse power 额定马力 rated horse power 马力重量系数 horsepower-weight factor 制动功率 brake horse power 制动热效率 brake thermal efficiency 总效率 overall efficiency 排烟极限功率 smoke limiting horsepower 功率曲线 power curve 机械损失 mechanical loss 机械效率 mechanical efficiency 有效热效率 effective thermal efficiency 充气系数 volumetric efficiency 过量空气系数 coefficient of excess air 适应性系数 adaptive coefficient 扭矩适应性系数 coefficient of torque adaptibility 转速适应性系数 speed adaptive coefficient 强化系数 coefficient of intensification 校正系数 correction factor 换算系数 conversion factor 活塞平均速度 mean piston speed 发动机转速 engine speed (rotational frequency) 怠速转速 idling speed 经济转速 economic speed 起动转速 starting speed 最低稳定工作转速 lowest continuous speed with load 最大扭矩转速 speed at maximum torque 最高空转转速 maximum no load governed speed 调速 speed governing 超速 overspeed 怠速 idling 转速波动率 speed fluctuation rate 工况 working condition(operating mode) 额定工况 declared working condition 变工况 variable working condition 稳定工况 steady working condition 空载 no-load 全负荷 full load 超负荷 overload 部分负荷 part load 充量（进气）charge 旋转方向 direction of rotation 顺时针 clockwise 逆时针 counter-clockwise 左转 left-hand rotation 右转 right-hand rotation 外径 major diameter 中径 pitch diameter 内径 minor diameter 径向间隙 radial clearance 发动机性能 engine performance 加载性能 loading performance 起动性能 starting performance 加速性能 acceleration performance 动力性能 power performance 排放性能 emission performance 空转特性 no load characteristics 负荷特性 part throttle characteristics 调速特性 governor control characteristics 万有特性 mapping characteristics 稳定调速率 steady state speed governing rate 气缸体和气缸盖 cylinder block and head 气缸体 cylinder block 整体铸造 cast inblock (cast enblock) 发动机罩 engine bonnet 气缸体加强筋 engine block stiffening rib 气缸 cylinder （转子机）缸体 stator 缸径 cylinder bore 气缸体机架 cylinder block frame 气缸盖 cylinder head 配气机构箱 valve mechanism casing 气缸体隔片 cylinder spacer 气缸盖密封环 cylinder head ring gasket 气缸盖垫片 cylinder head gasket 气缸套 cylinder liner(cylinder sleeve) 干式缸套 dry cylinder liner 湿式缸套 wet cylinder liner 气缸水套 water jacket 膨胀塞 expansion plug 防冻塞 freeze plug 气缸壁 cylinder wall 环脊 ring ridge 排气口 exhaust port 中间隔板 intermediate bottum 导板 guideway 创成半径（转子机）generating radius 缸体宽度（转子机）operating width 机柱 column 燃烧室 combustion chamber 主燃烧室 main combustion chamber 副燃烧室 subsidiary combustion chamber 预燃室 prechamber 涡流燃烧室 swirl combustion chamber 分开式燃烧室 divided combustion chamber 涡流式燃烧室 turbulence combustion chamber 半球形燃烧室 hemispherical combustion chamber 浴盆形燃烧室 bathtub section combustion chamber L形燃烧室 L-combustion chamber 楔形燃烧室 wedge-section combustion chamber 开式燃烧室 open combustion chamber 封闭喷射室 closed spray chamber 活塞顶内燃烧室 piston chamber 爆发室 explosion chamber 燃烧室容积比 volume ratio of combustion cahmber 燃烧室口径比 surface-volume ratio of combustion chamber 通道面积比 area ratio of combustion chamber passage 曲轴箱通气口 crankcase breather 凸轮轴轴承座 camshaft bearing bush seat 定时齿轮室罩 camshaft drive(gear)cover 曲轴箱检查孔盖 crankcase door 曲轴箱防爆门 crankcase explosion proof door 主轴承盖 main bearing cap 气缸盖罩 valve mechanism cover 飞轮壳 flywheel cover 扫气储器 scavenging air receiver 活塞 piston 裙部开槽活塞 split skirt piston U形槽活塞 U-slot piston 滚花修复活塞 knurled piston 圆顶活塞 dome head piston 平顶活塞 flat head piston 凸顶活塞 crown head piston(convex head piston) 凹顶活塞 concave head piston 阶梯顶活塞 step-head piston 筒形活塞 trunk piston 椭圆形活塞 oval piston 抗热变形活塞 autothermic piston 不变间隙活塞 constant clearance piston 镶因瓦钢片活塞 invar strut piston 直接冷却式活塞 direct-cooled piston 间接冷却式活塞 indirect cooled piston 滑裙活塞 slipper piston 活塞速度 piston speed 活塞顶部 piston head 活塞裙部 piston skirt 整体活塞裙 solid skirt 活塞裙扩大衬簧 piston skirt expander 滑履式活塞裙 slipper skirt 隔热槽 heat dam 活塞标记 piston mark 活塞销 piston pin 活塞销孔 piston pin boss 活塞销衬套 piston pin bushing 全浮式活塞销 full-floating piston pin 半浮式活塞销 semifloating piston pin 固定螺钉式活塞销 set screw piston pin 活塞环 piston ring 组合式活塞环 compound piston ring 同心活塞环 concentric piston ring 偏心活塞环 eccentric piston ring 自由环 free ring 闭合环 closed ring 梯形环 keystone ring 半梯形环 half keystone ring 矩形环 rectangular ring 油环 oil control ring 开槽油环 slotted oil control ring 螺旋弹簧加载双坡口油环 coil spring loaded slotted oil control ring 涨环 expander 双坡口油环 double bevelled oil control ring 内上坡口 internal bevel top 内下坡口 internal bevel bottom 边缘坡口油环 bevelled-ege oil control ring 刮油环 scrapper ring 钩形环 napier ring 镀铬活塞环 chrome plated piston ring 活塞衬环 piston ring expander 活塞环槽 piston ring groove 活塞环区 ring zone 活塞环岸 piston ring land 活塞环内表面 back of ring 曲柄连杆机构 connecting rod 中心曲柄连杆机构 central-located connecting rod 偏心曲柄连杆机构 offset connecting rod 铰接曲柄边杆机构 hinged connecting rod 连杆 connecting rod 连杆小头 connecting rod small end 连杆大头 connnecting rod big end 连杆杆身 connecting rod shank 副连杆 slave connecting rod 叉形连杆 fork-and-blade connecting rod 主连杆 main connecting rod 方形连杆 boxed rod 绞链式连杆 hinged type connecting rod 活节式连杆 articulated connecting rod 连杆盖 connecting rod cap 连杆轴承 connecting rod bearing 曲轴 crankshaft 整体式曲轴 one-piece crankshaft 组合式曲轴 assembled crankshaft 右侧曲轴 right-hand crankshaft 左侧曲轴 left-hand crankshaft 改变行程的曲轴 stroked crankshaft 曲轴前端 crankshaft front end 曲轴主轴颈 crankshaft main journal 轴颈重叠度 shaft journal overlap 圆角 fillet 主轴承 main bearing 曲轴止推轴承 crankshaft thrust bearing 薄臂轴瓦 thin wall bearing shell 曲轴油道 crankshaft oil passage 曲柄 crank 曲柄臂 crank arm 曲柄销 crank pin 轴套 bush 曲柄转角 crank angle 曲柄半径 crank radius 抛油圈 oil slander 角度轮 degree wheel 动平衡机 dynamic balancer 平衡重 balancer weight 扭振减振器 torshional vibration damper 扭振平衡器 torsion balancer 谐振平衡器 harmonic balancer 振动平衡器 vibration balancer 曲轴链轮 crankshaft sprocket 转子轴颈 rotor journal 偏心轴 eccentric shaft 曲轴箱 crankcase 闭式曲轴箱通风装置 closed-crankcase ventilating system 飞轮 flywheel 飞轮齿圈 flywheel ring gear 飞轮芯棒 cantilever 飞轮芯轴 flywheel spindle 飞轮的惯量矩 flywheel moment of inertia 飞轮标记 flywheel mark 当量系统 equivalent system 当量轴长 equivalent shaft length 一级往复惯性力 reciprocating inertia force,1st order 二级往复贯性力 reciprocating inertia force, 2nd order 离心惯性力 centrifugal inertia force 配气机构 valve gear 凸轮轴 camshaft 凸轮 cam 整体式凸轮轴 one-piece camshaft 组合式凸轮轴 assembled camshaft 凸轮轴驱动机构 camshaft drive 赛车用凸轮轴 race camshaft 凸轮轴轴颈 camshaft bearing journal 凸轮轴轴承 camshaft bearing 凸轮轴偏心轮 camshaft eccentric 凸轮轴链轮 camshaft sprocket 凸轮轴正时齿轮 camshaft timing gear 凸轮轴齿轮 camshaft gear wheel 进口凸轮 inlet cam 排气凸轮 exhaust cam 快升凸轮 quick lift cam 快升缓降凸轮 quick lift gradual clsing cam 凸轮轮廓 cam contour 凸轮包角 cam angle 凸轮升程 cam-lobe lift 凸轮尖 cam nose 凸轮从动件 cam follower 齿轮传动机构 gear drive 正时齿轮 timing gear 链传动机构 chain drive 链轮 sprocket wheel 链轮盘 chain sprocket 正时链条 timing chain 带齿皮带 toothed timing belt 链条张紧轮 chain tension gear 半速齿轮 half speed gear 正时齿轮刻印记号 timing gear punch mark 气门 valve 进气过程 intake process 换气过程 gas exchange process 扫气过程 scavenging process 给气比 delivery ratio 分层充气 stratified charge 充量系数 volumetric efficiency 涡流比 swirl rate 进气涡流 intake swirl 螺旋进气道进气 helical duct intake 导流屏式气门进气 masked valve intake 切向进气道进气 tangential duct intake 进气紊流 intake trubulence 进气提前角 intake advance angle 进气持续角 intake duration angle 进气迟后角 intake lag angle 进面值 time-area value 气门升程 valve lift 气门正时 valve timing 扫气口面积 scavenging port area 菌形气门 mashroom valve, poppet valve 钠冷却气门 sodium filled valve(natrium cooled valve) 双气门 dual valve 进气门 intake valve (suction valve,inlet valve) 排气门 exhaust valve 顶置气门 overhead valve 侧置气门 side valve 倾斜气门 inclined overhead valve 直立气门 vertical overhead valve 套筒式滑阀 sleeve valve 气门机构 valve gear 直接式气门驱动机构 direct valve gear 间接式气门驱动机构 indirect valve gear 气门杆 valve stem 加大气门杆 oversize valve stem 气门头 valve head 气门工作面 valve face 气门边限 valve margin 气门弹簧座 valve-spring retainer 气门锁片 valve key 气门间隙调节螺钉 valve lash adjusting screw 气门旋转器 valve rotator 气门室 valve cage 气门油封 valve oil seal 气门口 valve port 气门座 valve seat 气门座镶圈（嵌镶式气门座圈） valve seat insert(valve seat ring) 气门座锥角 valve seat angle 气门座宽度 valve seat width 气门挺杆 valve tappet(valve lifter) 液力挺杆 hydraulic tappet(lifter) 无间隙挺杆 zero-rush tappet (non-clearance tappet) 筒形挺杆 barrel type tappet 油压挺杆 ooil tappet 滚轮挺杆 roller tappet(lifter) 挺杆转位 tappet rotation 排气门挺杆 exhaust valve lifter 气门导管 valve guide 气门杆导管 stem guide 气门重叠度 stem overlap 气门开启持续时间 valve duration 气门正时标记 valve timing sign 气门弹簧 valve spring 气门内弹簧 inner valve spring 气门外弹簧 outer valve spring 刚性缓冲弹簧 stiff buffer spring 上紧弹簧 energizing spring 防振气门弹簧 non-surging spring 弹簧座圈 spring retainer 蝶形弹簧 belleville spring 滚柱 roller 气门室盖 valve chamber cover 摇臂 rocker arm 高升程摇臂 high lift rocker arm 摇臂轴 rocker arm shaft 推杆 push-rod 摇臂支架 rocker arm bracket 气门摇臂室罩 valve rocker chamber cover 导向轮 guide wheel 导杆 slide bar 导轨 slide rail 张紧轮 tensioning wheel 链条张紧调节装置 assembly chain tension adjuster 张紧带轮 tensioning pulley 传动带张紧装置 belt tensioner 同步驱动皮带 synchronous belt 同步驱动皮轮 synchronous belt pulley 供油系 fuel system 控制燃烧系统 controlled combustion system 反湿气装置 antipercolator 电子燃油喷射 electronic fuel injection 蒸气回收装置 vapor recovery system 燃油蒸气回收系统 fuel vapor recovery system 液体回收装置 liquid withdrawal system 恒量净化管 constant purge line 碳罐净化管 canister purge line 供油量 fuel delivery 循环供油量 fuel delivery per cycle 额定供油量 rated fuel delivery 怠速供油量 idling speed fuel delivery 供油规律 fuel supply rate curve 油量调节装置 fuel control unit 供油提前角 fuel supply advance angle 进油计量 inlet metering 几何供油行程 geometric fuel delivery stroke 供油率 fuel supply rate 燃油通道 fuel gallery 有效行程 effective stroke 剩余行程 remainder stroke 变行程计量 variable stroke metering 等容卸载 constant volume unloading 变容卸载 variable volume unloading 收缩容积 retraction volume 燃油喷油装置 fuel injection equipment 燃油喷射泵 fuel injection pump 滚轮式燃油喷射泵 roll fuel injection pump 凸轮轴式燃油喷射泵 camshaft fuel injection pump 直列式燃油喷射泵 in-line fuel injection pump 伺服式燃油喷射泵 servo fuel injection pump 底部突缘安装燃油喷射泵 base flanged mounted fuel injection pump 上部安装燃油喷射泵 high flanged-mounted fuel injection pump 侧向安装燃油喷射泵 side-mounted fuel injection pump 端部突缘安装式燃油喷射泵 end flange-mounted fuel injection pump V形燃油喷射泵 vee fuel injection pump 脉动式燃油喷射泵 jerk fuel injection pump 螺纹安装燃油喷射泵 screw-mounted fuel injection pump 蓄能式燃油喷射泵 accumulator fuel injection pump 往复式燃油喷射泵 reciprocating fuel injection pump 驱动轴式燃油喷射泵 driveshaft fuel injection pump 单缸式燃油喷射泵 single cylinder fuel injection pump 圆柱式燃油喷射泵 cylindrical fuel injection pump 旋转式燃油喷射泵 rotary fuel injection pump 分配式燃油喷射泵 distributor fuel injection pump 多缸燃油喷射泵 multicylinder fuel injection pump 框架安装式燃油喷射泵 cradle mounted injection pump 喷油始点 fuel injection beginning 喷油终点 fuel injection end 喷油持续角 fuel injection duration angle 喷油延迟 injection delay 引燃喷射 pilot injection 启喷压力 injection starting pressure 峰值喷油扭矩 peak injection torque 峰值喷油压力 peak injection pressure 喷油泵油缸数目 number of cylinders of an injection pump 无气喷射 solid injection 喷射正时 injection timing 集中喷射 group injection 喷油器 injector 整体式喷油器 unit injector 喷嘴 nozzle 轴针式喷嘴 pintle type nozzle 环槽式喷嘴 annular slot nozzle 孔式喷嘴 hole type nozzle 长杆喷嘴 long stem nozzle 孔板式喷嘴 orifice plate nozzle 开式喷嘴 open nozzle 闭式喷嘴 closed nozzle 喷油提前器 timing advance unit 喷射泵壳体 injection pump housing 针阀 needle 芯轴 central spindle 喷嘴壳体 nozzle body 针阀升程 needle lift 喷嘴盖形螺母 nozzle cap nut 喷油器壳体 nozzle holder 突缘安装喷油器壳体 flanged-mounted injection nozzle holder 燃油喷射泵传动装置 transmision of an injection pump 喷嘴锥体 nozzle hole cone 柱塞 plunger 柱塞套 barrel 柱塞行程 plunger stroke 喷孔 spray orifice 海拔控制器 altitude control 提前器飞锤 flyweight 喷孔长径比 ratio of nozzle hole length nozzle diameter 喷嘴液动力特性 nozzle hydrokinetic characteristics 动态相位 dynamic phase 喷孔面积 nozzle hole area 喷嘴流通特性 nozzle flow characteristic 喷油背压 injection back pressure 高压油管 high pressure pipe 平均喷油扭矩 mean injection torque 喷油总效率 overall pumping efficiency 峰值喷油压力 injection peak pressure 预行程 prestroke 收缩行程 retraction stroke 燃油箱 fuel tank 油箱盖 fuel tank 油位表 fuel level gauge 注油控制装置 fill control system 汽油箱 gasoline tank( petrol tank) 汽油供给管 gasoline feed pipe 加油管 filler tube 放油螺塞 drain plug 吸油管 suction pipe 刚性燃油管 rigid fuel pipe 进油孔 fuel feed hole 供油管 supply pipe 通气管 bleeding pipe 通气管 bleeding pipe 泄油阀 spill valve 泄油孔口 spill port 进油阀 inlet valve 最大油量限制器 maximum fuel stop 滴油 dribble 燃油表 fuel gauge 输油泵 feed pump 燃油泵 fuel pump 附装燃油箱中的电动燃油泵 tank-mounted eletric fuel pump 机械式燃油泵 mechanical fuel pump 膜片式燃油泵 diaphragm fuel supply pump 叶片式供油泵 vane fuel supply pump 活塞式输油泵 piston type fuel supply pump 齿轮式输油泵 gear fuel supply pump 电动燃油泵 eletric fuel pump 带真空泵的汽油泵 vacuum pump with fuel pump 起动加油器 primer 起动给油杆 primer lever 燃油泵上体 fuel pump body 燃油泵下体 fuel pump base 燃油泵盖 bowl cover 进油口接头 fuel inlet neck 出油口接头 fuel discharge port 输出阀 delivery valve 泵油元件 pump element 回油阀部件 fuel return valve assembly 化油器 carburetor 化油器系统 carburetor circuit 简单化油器 elementary carburetor 单腔化油器 single-barrel carburetor 双腔并动化油器 two-barrel dual carburetor 双腔分动化油器 two-barrel duplex carburetor 四腔化油器 four-barrel carburetor 上吸式化油器 updaught carburetor 下吸式化油器 downdraught carburetor 平吸式化油器 horizontal carburetor 侧吸式化油器 side-draft-carburetor 高海拔补偿式化油器 altitude compensating carburetor 化油器附加器 adaptor carburetor 双腔式化油器 twin-choke carburetor 固定喉管式化油器 fixed venturi carburetor 可变喉管化油器 variable venturi carburetor 化油器接头 carburetor adaptor 阻风门 choke valve 阻风活塞 choke piston 阻风板 choke plate 自动阻风门 automatic choke 阻风门拉钮 choke button 电控自动阻风门 electric-assisted choke 阻风管 choke tube 喉管 venturi 双重或三重喉管 double & triple venturi 阻风门拉线 choke cable 化油器小喉管 booster venturi 浮子系 float system 浮子 float 环形浮子 annular float 同心式浮子 concentric float 浮子支销 float hinge pin 浮子针阀 float needle valve 阀针 valve needle 浮子油面 float level 浮子臂 float arm 侧置浮子室式 side float type 怠速阀 idle valve 怠速针阀 idle needle 省油器 economizer 省油器阀 economizer valve 辅助空气阀 auxiliary air-valve 加速油井 accelerating well 加速泵 accelerating pump 加速泵喷嘴 accelerating pump nozzle 油门 throttle 手油门 hand throttle 节气门操纵手柄 throttle control lever 真空加浓器 vacuum booster 加浓器 excess fuel device 量孔体 jet block 怠速量孔 idle metering jet 主量孔 main metering jet 剂量阀活塞 dosage valve piston 空气量孔 air jet 燃油滤清器 fuel filter 沉淀杯 sediment bowl 串联过滤器 in-line filter 燃油箱内装过滤器 in-tank filter 调速器 governor 飞球式调速器 flyball governor 调速器 governor 飞球式调速器 flyball governor 液压调速器 hydraulic governor 真空转速调速器 vacuum speed governor 惯性调速器 inertia governor 离心调速器 centrifugal governor 调速器重锤 governor weight 空气滤清器及进排气系统 air cleaner and intake and exhaust sytem 空气滤清器 air filter 冲压式空气滤清器 ram air clearner 恒温控制式空气滤清器 thermostatic controlled air cleaner 油浴式空气滤清器 oil bath air cleaner 纸质空气滤 清器 paper air clearner 旋流管式空气滤清器 swirl tube air filter 滤清器滤芯 filter element 空气滤清器壳体 air filter housing 空气滤清器盖 air filter cover 滤清器密封圈 filter seal ring 滤网 sieve 滤纸盘或膜 filter paper disc or membrane 进气和排气系统 intake and exhaust system 排气管 exhaust pipe 排气抽气管 exhaust extraction duct 扫气泵 scavenging pump 进气预热装置 intake preheater 进气歧管 intake manifold 进气歧管真空度 intake manifold vacuum 冷式进气歧管 cold manifold 冲压式进气歧管 ram intake manifold 排气歧管 exhaust manifold 脉冲式排气歧管 pulse exhaust manifold 等压排气歧管 constant pressrue exhaust manifold 排气歧管热量控制阀 exhaust manifold heat control valve 超高度歧管 high-rise manifold 升温横跨管道 heat crossover 排气横跨管道 exhaust crossover 预热点 hot spot 阻风门加热器 choke heater 热空气导流管 hot air duct 隔热板 heat shield 排气再循环阀 exhaust -gas-recirculation 消声器 silencer 进气消声器 intake silencer 排气消声器 exhaust silencer 金属垫片式消声器 steel pack muffler 玻璃丝消声器 glass pack muffler 空洞消声器 gutted muffler 前排气管 front exhaust pipe 尾管 tail pipe 消声器联接管 intermediate pipe 热空气管 hot air pipe 曲轴箱通风管 crankcase bleed pipe 隔声罩 acoustic hood 进气消声器元件 silencer element 真空泵 vacuum pump 指示功率 indicated power 指示热效率 indicated thermal efficiency 指示油耗率 indicated specific energy consumption 示功图 indicator diagram 冷却系 cooling system 风冷 air cooling 水冷 water-cooling 循环流冷却系 cooling recovery system 自然循环液冷却系统 natural circulation type cooling system 热流循环液冷却系统 thermo-siphon circulation type cooling system 温差循环液冷却系统 gravity circulation water cooling system 压力式水冷却系统 positive circulation cooling system 加压式冷却法 pressure type cooling 水泵循环冷却系统 pump circulation cooling system 强制循环式化冷系统 forced-feed water circulation system 封闭式液冷系统 sealed cooling system 散热器 radiator 片式散热器 finned radiator 管式散热器 tubular radiator 蜂窝式散热器 cellular radiator 哈里逊式散热器 Harrison type radiator 带板式散热器 ribbon type radiator 上水箱 upper tank 下水箱 lower tank 涨溢箱 expansion tank 散热器芯 radiator core 之字形管散热器芯 film core 管-片式散热器芯 fin and tube core 散热器加水口盖 radiator filter cap 压力式水箱盖 radiator-pressure cap 蒸气-空气泄放阀 vapor-air release valve 散热器护罩 radiator cowl 散热器百叶窗 radiator shutter 散热器保温帘 radiator roller blind 散热片 cooling fin 缸盖散热片 cylinder head fin 缸体散热片 cylinder block fin 控温装置 temperature regulating device 恒温器 thermostat 恒温器主阀 thermostat main valve 恒温器旁通阀 thermostat by-pass valve 恒温器挠性波纹筒 thermostat flexible bellows 液体冷却设备 liquid cooling equipment 水泵 water pump 水泵体 pump casing 水泵叶轮 water pump impeller 旁通进水口 water by-pass inlet neck 循环泵 circulating pump 主进水口 water main inlet port 出水口 water outlet port 自调式水封 self-adjusting seal unit 溢流管 overflow pipe 导流板 deflector 风扇 fan(blower) 轴流式风扇 axial flow fan 离心式风扇 centrifugal fan 风扇壳体 blower casing 风扇导流罩 fan cowl 风扇毂 fan hub 风扇叶片 fan blade 风扇叶轮 blower impeller 风扇导流定子 blower stator 风扇皮带轮 fan pulley 三角皮带 v-belt 风扇护罩 fan shroud 风扇叶轮叶片 impeller vane 冷却用空气 cooling air 风扇导流叶片 stator vane 强制风冷 forced-air cooling 自然风冷 natural air cooling 风道 air ducting 润滑系 lubrication system 润滑 lubrication 气缸上部润滑 upper cylinder lubrication 压力润滑 pressure-feed lubrication 压力润滑法 forced lubrication 自动润滑 automatic lubrication 飞溅润滑 splash lubrication 润滑周期 lubrication interval 边界润滑 borderline lubrication 曲轴箱机油油盘 crankcase oil pan 油底壳 oil pan 机油盘放油塞 sump plug 集油器 oil collector 机油泵 oil pump 计量式机油泵 metering oil pump 齿轮式机油泵 gear type oil pump 转子式机油泵 rotor-type oil pump 机油泵出油管 oil pump outlet pipe 放油口 oil drain hole 油道 oil duct 断油开关 cut-off cock 机油散热器 oil cooler 机油滤清器 oil filter 机油粗滤器 primary oil filter 机油精滤器 secondary oil filter 全流式机油滤清器 full-flow oil filter 分流式机油滤清器 by-pass oil filter 离心式机油滤清器 centrifugal oil filter 整体式滤芯 integral filtering element 细滤器滤芯 filter element 滤清器壳 filter box 滤片 filtering disc 机油减压器 oil pressure relief valve 旁通阀 by-pass oil filter 机油滤网 oil strainer 加机油孔 oil filter cap 滤芯轴 filter shaft 刮片组件 cleaning edge 机油量尺 dipstick 机油滤网 oil strainer 增压器 supercharger 增压和扫气装置 pressure-charging and scavenging unit 增压装置 supercharging device 涡轮增压器 turbo-charger 气波增压器 comprex pressure wave supercharger 增压器阻风阀 supercharger blast gate 增压器调节容气量的旁通阀 supercharger control bypass 增压器叶轮 supercharger impeller 惯性增压 inertia supercharging 机械增压 mechanical supercharging 涡轮增压 turbo-charging 增压比 supercharge ratio 增压压力 boost pressure 增压中冷 inter-cooling 中冷度 inter-cooling level 增压度 supercharging level 喘振 surge 喘振线 surge line 轴流式涡轮 axial-flow turbine 脉冲进气 ram charging 发动机试验 engine test 发动机试验规程 engine test procedure 发动机技术要求 engine technical requirements 标准大气状况 standard atmospheric conditions 大气压力 atmospheric pressure 进气温度 inlet air temperature 进气温度 inlet air temperature 功率校正 power correction 功率标定 power rating 功率换算 power conversion 校正系数 correction factor 换算系数 performance test 性能试验 performance test 起动性能试验 starting ability test 怠速试验 idle running test 道路负荷试验 road load test 各缸工作均匀性试验 cylinder variation test 背压试验 back pressure test 最低稳定工作转速试验 lowest continuous speed test with load 背部泄漏试验 back-leakage test 调整试验 adjustment test 热平衡试验 heat balance test 快速磨损试验 accelerated wear test 热冲击试验 thermo-shock test 空载特性试验 no-load characteristic test 模拟增压试验 simulated supercharging test 停缸试验 cylinder fuel-cut test 增压机匹配试验 turbo-charger matching test实践证明经常访问无忧英语教育网 www.51education.net ,能迅速提高你的英语学习能力!积沙成塔,不断提高! 本站所提供的所有信息仅供学校课堂教学及英语学习者学习研究之用，其著作权归原作者及媒体所有。 |
||
| 文章录入：soosun 责任编辑：soosun |
||
|
|
||
| 【发表评论】【加入收藏】【告诉好友】【打印此文】【关闭窗口】 | ||
| 最新热点 | 最新推荐 | 相关文章 | ||
| 节日必备：如何用英语买到称… On her own, but not alone “发疯”的两种新潮英语说法 国外生活必备英文词汇－住宿… 几个流行词 第30课：与选举有关的词汇 雅思范文：谈谈你身边城市交… 禽流感常用英语词汇及生化术… 雅思词汇与句型总结 雅思阅读词汇：自然与科技－… |
| 网友评论：（只显示最新10条。评论内容只代表网友观点，与本站立场无关！） |
| |Sitemap地图 | 设为首页 | 加入收藏 | 联系站长 | 友情链接 | 版权申明 | 网站公告 | 管理登录 | | |||
|
